Woodworking Guide - Flipbook - Page 35
5°
15°
12°
ATB GRIND
MODERATE ANGLE
SCORING PARTICLE
BOARD & DOUBLE
SIDED MDF LAMINATE
DOUBLE-SIDED MELAMINE
EXCELLENT
BELTS
Used on panel saws and sliding table saws (ex. SCM,
& Altendorf), with separate scoring units for chipfree cuts on both sides of the material. Adjustable
scoring sets consist of two 12-tooth saw blades with
shims to adjust the kerf width (2.8mm to 3.6mm).
These are used in combination with our plywood/
laminate series Triple chip blade above.
DISCS
ADJUSTABLE SCORING SETS
PLASTIC LAMINATE
EXCELLENT
SHEETS
Price
$187.62
ROLLS
SLIDING TABLE
PANEL SAW
WARNING: Not recommended for cutting non-ferrous alloys.
Dia.
120mm
Teeth
12x2
Kerf
MM
Inch
2.8-3.6 .110-.144
Plate
Inch
.087(x2)
Hook
Angle
12°
SAWBLADES 2
Bore Pin-Hole MAX RPM
Tool No.
22mm
—
15,900
KSB120-T14
SAWBLADES 3
SAWBLADES 4
SAW BLADE APPLICATION GUIDE
RIP:
35
SAWBLADES
REFERENCE
Visit us online: www.klingspor.com
TOOLS
KSB10-240 – More aggressive, faster & leaves a rougher cut
KSB10-301 – Less aggressive and better edge finish
KSB10-240TKT – Thin Kerf
Crosscut: KSB10-800 / KSB12-960 (For use on a table saw)
KSB10-500
KSB10-806 / KSB12-106 (For use on Miter saws, sliding miter saws & Radial Arm)
Combo
(Rip & crosscut wood, plywood, chipboard):
KSB10-500 Better overall results on solid wood
KSB10-400 More aggressive and faster for rough cutting in wood
KSB10-504TKT – Thin Kerf
MELAMINE:
PLYWOOD:
KSB10-803 / KS12-963
KSB10-601(Single-sided only – may chip on the back side)
PLASTIC:
KSB10-801(same blade, but with more teeth – 80 vs 60)
KSB10-802 (Phenolic & hard plastics)
KSB12-721 & 721-30
KSB10-728 (Plexiglass)
(Single-sided only – may chip the back side)
KSB10-805 / KSB12-105 (Phenolic, Hard plastics &
KSB10-800 (Different tooth configuration – ATB –
aluminum)
and better for double-sided & prefinished plywood
NON-FERROUS (Brass, copper, aluminum, etc.):
applications). Also good for crosscutting solid wood.
KSB10-805 / KSB12-105 (Thin wall – less than 1/4”)
LAMINATE (single sided):
KSB10-605 (Thick wall - greater than 1/4”)
KSB10-728 Solid surface blade
KSB10-802 Plastic blade
MITER CUTS:
KSB10-803 / KSB12-963 Melamine blade
KSB10-806 10” Miter Blade
MDF/Chipboard:
KSB12-106 12” Miter Blade
KSB10-801 Plywood/Laminate
KSB10-816TKT 12” Thin Kerf Miter
KSB10-803 / KSB12-963 Melamine blade
KSB10-606TKT 10” Thin Kerf Sliding Miter
KSB12-726TKT 12” Thin Kerf Sliding Miter
SOLID WOOD:
FOAM PADS FLAPWHEELS NON-WOVEN SPECIALTY SAWBLADE ROUTER BIT
SAWBLADES 1
MM
2.2(x2)
