Router Bits Guide - Flipbook - Page 25
GLUE JOINTS
3374A
3374B
VEE PANEL TONGUE &
GROOVE Ball Bearing Guide
Vee Panel TongueStraight Tongue & Groove bits are the ideal
bits for joining two boards together where strength and
alignment are important. This set makes the Tongue and Groove joint in its simplest form. Both sides
of the joint are straight and square. Each side is formed with its own bit. This set works best when used
in a router table with the fence in line with the bearing. Carbide tipped, two-wing cutter & Groove bits
this set makes a tongue and groove joint with a decorative V groove along the length of the joint. It is
typically used in tongue and groove paneling or ceilings. This set should only be used in a router table
with the fence in line with the bearing. Carbide tipped, two-wing cutter
PART
NUMBER
MATERIAL
THICKNESS
LARGE
DIAMETER
CUTTING
LENGTH
OVERALL
LENGTH
1/2" SHANK
3374
5/8-1"*
1-5/8"
1"
3506
3508
TONGUE & GROOVE ASSEMBLY
Tongue & Groove Assembly bit is the most economical way to make tongue and groove joints. The
single bit is used to make both sides of the joint, simply by adjusting the height of the bit to change
from tongue to groove. Carbide tipped.
CUTTING
LENGTH
OVERALL
LENGTH
1/2" SHANK
3375
1/2" - 13/16"
Replacement Parts:
1-5/8"
9/32"
NUMBER
OF SIDES
STOCK
(MAXIMUM)
LARGE
DIAMETER
6 or 12
8
7/8"
7/8"
1-7/8"
1-3/4"
On six and eight sided objects, the exterior side is cut face up on a router table. Twelve and sixteen
sided objects are cut face down. The same bit (#3506) is used for six sided and twelve sided objects.
Either Flush or Ribbed (outside corners protruding) construction is possible. Ribbed construction
is recommended with 12 and 16 sides because the interior leg of the notch will be very small when made
flush. Outside corners on ribbed construction can be cut or sanded down for flush appearance if desired.
Location of the inside corner of the notch (i.e.- vertical bit adjustment) is important for final
finish appearance. The outside leg of the notch (closest to the exterior) should be the same length as
the stock thickness for flush construction. This will put the inside corner of the notch in the center of the
stave on six sided flush projects. The inside corner will be below center (furtherest from exterior side) on
all others. Allow extra stock to experiment and set corner height as desired. Move notch towards exterior
side (raise the bit) to increase rib size (amount of outside corner protruding). Move notch away from
exterior side (lower the bit) to decrease amount of rib. Note: Bit adjustment is reversed on twelve and
sixteen sides since those staves are cut face down.
ONE TOOL MAKES BOTH CUTS
LARGE
DIAMETER
A great way to join up many multi-side projects (planters, columns, barrels, etc.). Very straightforward,
this joint requires routing a notch in only one edge of each stave (side). Notching also improves ease
of assembly and total glue area. All bits are 1/2" shank and are designed for use in a router table with
a fence guide.
1/2" SHANK
* Material over 1" thick requires a second cut on the tongue profile to waste away excess stock.
MATERIAL
THICKNESS
MULTI SIDE BITS
PART
NUMBER
2-3/4"
Order 3374 for two piece set.
Order 3374A or 3374B for individual cutters.
PART
NUMBER
PART #3506
B5
Groover - 6628
Arbor - A260
EDGE BANDING SET
This bit set will allow the customer to make their own hardwood edge banding
for plywood, particle board, or MDF stock. It enables them to make their own
hardwood edge banding match the rest of the project instead of having to buy
a thin veneer edge tape to be glued on. It’s designed for stock up to 3/4" thick,
which is standard sheet good thickness, and features carbide tips and 1/2"
shank. The advantage of this is a stronger edge than that of the thin veneer
tape. It can be routed with a profile or left square depending on the application.
Adding hardwood banding to veneered plywood shelves and table tops.
• One bit will put a "V" shaped, concave profile in the plywood.
• While the other bit forms a perfect match in hardwood.
• Top and bottom of the banding can be trimmed flush using the router
or hand plane.
• For use on stock that is less than 13/16" in thickness.
Couple these router bits
with Klingspor’s
Glue Line Ripping saw
blade to make all
of your glue joint projects
a breeze.
3401 Plywood Cutter • 3402 Edge Band Cutter
PART
NUMBER
CUTTER
LENGTH
MATERIAL
THICKNESS
1/2" SHANK
3400
13/16"
3/4"
Visit us online: www.klingspor.com
25
ROUTER BITS
