Router Bits Guide - Flipbook - Page 24
GLUE JOINTS
Locking Drawer Glue Joint bits (3346, 3347, 3350, &3352) are the perfect tool for making drawers
from wood. One bit does it all. After the proper height is set, it is just a matter of running the drawer
front with the outside face up, flat on the table. The side pieces are machined vertically, their inside
faces against the fence and cutter. Carbide tipped, two-wing cutter.
ONE TOOL MAKES BOTH CUTS
LOCKING DRAWER GLUE JOINTS
45° LOCK MITER
45° Lock Miter bits deliver double the glue surface of a traditional 45° miter.
It creates both the miter and a joint lock at the same time, which prevents
movement when clamping pressure is applied. Board "A" is ran horizontally, while board "B" is ran vertically. Carbide tipped, two-wing cutter.
PART
NUMBER
3360
3362
DRAWER FRONT
ONE TOOL MAKES BOTH CUTS
PART
NUMBER
3346
3347
LARGE
DIAMETER
3/4"
1"
CUTTING
LENGTH
SHANK
DIAMETER
1/2"
1/2"
1/4"
1/2"
MATERIAL
THICKNESS
1/2" - 1-1/4"
1/2"- 3/4"
LARGE
DIAMETER
3-1/8"
2"
SHANK
DIAMETER
1/2"
1/2"
OVERALL
LENGTH
2-7/8"
2-3/8"
Note: 3362 is recommended for stock thickness 1/2 - 3/4"
OVERALL
LENGTH
1-7/8"
2-1/8"
LOCKING DRAWER GLUE JOINTS
WEDGE TONGUE
& GROOVE
Wedge Tongue & Groove bits are the ideal bits for joining two boards together where strength and
alignment are important. This set is for joints that are glued along the length. The wedge shape of the
tongue increases the glue surface - adding to the strength of the joint. This set should only be used in a
router table. Carbide tipped, two-wing cutter
ONE TOOL MAKES BOTH CUTS
PART
NUMBER
MATERIAL
THICKNESS
LARGE
DIAMETER
3370
3352
LARGE
DIAMETER
1"
CUTTING
LENGTH
1"
OVERALL
LENGTH
1-1/4"
2-7/8"
1/2" SHANK
DRAWER FRONT
PART
NUMBER
SHANK
DIAMETER
SHANK
DIAMETER
1/2"
5/8" - 1-1/4"
1-1/4"
* Order 3370 for Two Piece Set.
* Order 3370A or 3370B for individual cutters.
OVERALL
LENGTH
2-3/8"
3373A
3373B
STRAIGHT
TONGUE & GROOVE
ONE TOOL MAKES BOTH CUTS
Ball Bearing Guide
Straight Tongue & Groove bits are the ideal bits for joining two boards together where strength and
alignment are important. This set makes the Tongue and Groove joint in its simplest form. Both sides of
the joint are straight and square. Each side is formed with its own bit. This set works best when used in
a router table with the fence in line with the bearing. Carbide tipped, two-wing cutter
STANDARD GLUE JOINT
Standard Glue Joint bit provides lots of glue surface to join boards together. One cutter makes both
cuts, so no need to make two set-ups. Board "A" runs face down and board "B" face up. A test piece
may be required to fine tune the set up. Carbide tipped two wing cutter.
PART
NUMBER
MATERIAL
THICKNESS
LARGE
DIAMETER
SHANK
DIAMETER
PART
NUMBER
OVERALL
LENGTH
1/2" - 1-1/4"
1-1/2"
ROUTER BITS
1/2"
LARGE
DIAMETER
SHANK
DIAMETER
OVERALL
LENGTH
1-1/4"
3-1/8"
1/2" SHANK
3373
3354
MATERIAL
THICKNESS
2-3/4"
1/2" - 1-1/4"
1-1/4"
* Order 3373 for two piece set
* Order 3373A or 3373B for individual cutters.
Bearing Number: B7
24
Call Toll Free 800-645-5555
