Router Bits Guide - Flipbook - Page 20
TEMPLATE •T-SLOT
TEMPLATE BITS
KEYHOLE BITS
Ball Bearing Guide Template Bits with ball bearing guide are similar to a flush trim
Keyhole bits are used to create a small keyhole slot on the back of picture frames, plaques, signs, etc.
Simply plunge the bit and make a groove in the proper direction to allow for a screw or nail to hold the
workpiece on the wall. Carbide tipped.
in that they will trim the workpiece flush, but the bearing is on the top (near the shank) of the cutter
instead of the bottom. KLINGSPOR template bits use replaceable bearings and lock collars. Carbide
tipped. Two-wing cutter.
PART
NUMBER
CUTTING
DIAMETER
CUTTING
LENGTH
OVERALL
LENGTH
PART
NUMBER
BEARING
NUMBER
1/2"
1/2"
1/2"
1/2"
1/2"
5/8"
5/8"
5/8"
5/8"
3/4"
3/4"
3/4"
3015
7/8"
1/8"
1/4"
1/2"
3/4"
1"
1/4"
1/2"
3/4"
1"
1/4"
3/4"
1"
1-3/4"
1-7/8"
2"
2-1/4"
2-1/2"
1-3/4"
2-1/4"
2-1/2"
2-1/2"
1-3/4"
2-3/8"
2-5/8"
SMALL
DIAMETER
CUTTING
LENGTH
OVERALL
LENGTH
7/16"
7/16"
1-1/2"
1-1/2"
7/16"
7/16"
2-1/8"
2-1/8"
1/4" SHANK
1/4" SHANK
* 3000A
* 3000
3001
3002
3004
* 3006
K41
K43
3008
* 3010
3012
3014
LARGE
DIAMETER
B9
B9
B9
B9
B9
B6
B6
B6
B6
B4
B4
B4
3050
3052
3/8"
1/2"
3051
3053
3/8"
1/2"
3/16"
5/16"
1/2" SHANK
3/16"
5/16"
3/8" SHANK
1"
2-5/8"
B12
B
1/2" SHANK
***
***
***
***
3016
3018
3019
3020
3021
3022
3022A
3023
1-1/8"
1-1/8"
1-1/8"
3/4"
3/4"
3/4"
7/8"
3/4"
1"
1-1/2"
2"
1"
1-1/4"
1-1/2"
1-1/2"
2"
3"
3-1/2"
4"
2-3/4"
3"
3-1/4"
3-1/2"
3-5/8"
B11
B11
B11
*** B19
*** B19
*** B19
B13
*** B19
A
PART # 3075
PART # 3070
T-SLOT CUTTER
T-Slot Cutter "Slatwall" bits create a T-slot in wood for making jigs and fixtures in the shop.
This allows a bolt to slide the length of the slot for easy adjustment of the jig. Carbide tipped.
PART
NUMBER
* Dado Clean out bits. Use to Square the bottom of dado cuts made on a table saw.
*** KLINGSPOR recommends using bits over 3/4" diameter in 1/2" shank whenever
possible due to the fragile nature of the B19 bearing.
LARGE
DIAMETER
SMALL
DIAMETER
"A"
LENGTH
"B"
OVERALL
LENGTH LENGTH
1/2" SHANK
3070
3075
1-1/16"
1-3/16"
3/8"
3/8"
5/16"
1/4"
1/2"
3/8"
2-3/8"
2-3/8"
TEMPLATE BITS
With Oversize Bearings Template bits with over size bearings are similar to a
template bit in that they have a bearing on the top of the cutter but instead of trimming flush, they
offset the cut. These are made to replace bits and work with specific router jigs. KLINGSPOR template
bits use replaceable bearings and lock collars. Carbide tipped. Two-wing cutter.
PART
NUMBER
CUTTING CUTTING
DIAMETER LENGTH
OVERALL
LENGTH
BEARING
DIAMETER
BEARING
NUMBER
1/2"
5/8"
3/4"
5/8"
B9
B6
B4
B6
SLOT & UNDERCUT BITS
Used to cut all types of slots and grooves. Also used to undercut decorative patterns or large letters
to give them a bold appearance. This can even be used by hardwood flooring contactors to replace
boards in existing floors. They have a replaceable bearing and collar. Carbide tipped.
1/4" SHANK
1
2
3
1,4
3025
3027
3028
3032
5/16"
1/2"
1/2"
9/16"
3/4"
1/4"
1/4"
3/4"
2-3/4"
1-7/8"
1-7/8"
2-1/4"
LARGE
DIAMETER
3094
*3094B
3098
* 3098B
3110
* 3110B
3/4"
3/4"
1"
1"
1-1/2"
1-1/2"
"A"
LENGTH
"B"
DEPTH
OVERALL
LENGTH
1/4" SHANK
For Porter-Cable Mortenª, Mortise & Tenon Jig, and Omnijig¨ templates
Porter-Cable Hinge Butt Mortise Bit
3 For Hinge-Mateª II Template
4 Keller Box Joint Bit
1
2
ROUTER BITS
PART
NUMBER
1/8"
1/8"
1/4"
1/4"
1/4"
1/4"
1/4"
1/8"
3/8"
1/4"
5/8"
1/2"
1-7/8"
1-7/8"
2"
2"
2"
2"
* B denotes Bearing (B9) guide on shank.
20
Call Toll Free 800-645-5555
