2025 KLINGSPOR BIG Catalog - Catalog - Page 118
3374A
3374B
VEE PANEL TONGUE &
GROOVE Ball Bearing Guide
Vee Panel Tongue Straight Tongue & Groove bits are the ideal bits for joining two boards together where strength and alignment are important. This
set makes the Tongue and Groove joint in its simplest form. Both sides of
the joint are straight and square. Each side is formed with its own bit. This
set works best when used in a router table with the fence in line with the
bearing. Carbide tipped, two-wing cutter & Groove bits this set makes a
tongue and groove joint with a decorative V groove along the length of the
joint. It is typically used in tongue and groove paneling or ceilings. This set
should only be used in a router table with the fence in line with the bearing.
Carbide tipped, two-wing cutter
Part
Number
Material
Thickness
Large
Diameter
Cutting
Length
Overall
Length
Price
2-3/4"
$344.78
1/2" SHANK
3374
5/8-1"*
1-5/8"
1"
Order 3374 for two piece set.
Order 3374A or 3374B for individual cutters.
* Material over 1" thick requires a second cut on the tongue profile to waste away excess stock.
PART #3506
MULTI SIDE BITS
A great way to join up many multi-side projects (planters, columns, barrels,
etc.). Very straightforward, this joint requires routing a notch in only one edge
of each stave (side). Notching also improves ease of assembly and total glue
area. All bits are 1/2" shank and are designed for use in a router table with a
fence guide.
Part
Number
Number
Of Sides
3506
3508
6 or 12
8
Stock
(Maximum)
Large
Diameter
Price
1-7/8"
1-3/4"
$111.75
$111.75
1/2" SHANK
7/8"
7/8"
On six and eight sided objects, the exterior side is cut face up on a
router table. Twelve and sixteen sided objects are cut face down. The same
bit (#3506) is used for six sided and twelve sided objects.
ONE TOOL MAKES BOTH CUTS
TONGUE & GROOVE ASSEMBLY
Tongue & Groove Assembly bit is the most economical way to make tongue
and groove joints. The single bit is used to make both sides of the joint,
simply by adjusting the height of the bit to change from tongue to groove.
Carbide tipped.
Part
Number
Material
Thickness
Large
Diameter
3375
1/2" - 13/16"
1-5/8"
Cutting
Length
Overall
Length
Price
1/2" SHANK
Replacement Parts:
9/32"
B5
$133.16
Groover - 6628
Arbor - A260
EDGE BANDING SET
This bit set will allow the customer to make their own
hardwood edge banding for plywood, particle board, or
MDF stock. It enables them to make their own hardwood
edge banding match the rest of the project instead of
having to buy a thin veneer edge tape to be glued on.
It’s designed for stock up to 3/4" thick, which is standard
sheet good thickness, and features carbide tips and 1/2"
shank. The advantage of this is a stronger edge than that
of the thin veneer tape. It can be routed with a profile or
left square depending on the application. Adding hardwood
banding to veneered plywood shelves and table tops.
• One bit will put a "V" shaped, concave profile in the plywood.
• While the other bit forms a perfect match in hardwood.
• Top and bottom of the banding can be trimmed flush using the router
or hand plane.
• For use on stock that is less than 13/16" in thickness.
Cutter
Length
3400
13/16"
Material
Thickness
Location of the inside corner of the notch (i.e.- vertical bit adjustment)
is important for final finish appearance. The outside leg of the notch (closest
to the exterior) should be the same length as the stock thickness for flush
construction. This will put the inside corner of the notch in the center of the
stave on six sided flush projects. The inside corner will be below center
(furtherest from exterior side) on all others. Allow extra stock to experiment
and set corner height as desired. Move notch towards exterior side (raise
the bit) to increase rib size (amount of outside corner protruding). Move
notch away from exterior side (lower the bit) to decrease amount of rib. Note:
Bit adjustment is reversed on twelve and sixteen sides since those staves
are cut face down.
Couple these router
bits with Klingspor’s
Glue Line Ripping saw
blade to make all
of your glue joint
projects a breeze.
3401 Plywood Cutter • 3402 Edge Band Cutter
Part
Number
Either Flush or Ribbed (outside corners protruding) construction
is possible. Ribbed construction is recommended with 12 and 16 sides
because the interior leg of the notch will be very small when made flush.
Outside corners on ribbed construction can be cut or sanded down for flush
appearance if desired.
Price
1/2" SHANK
3/4"
Visit us online: www.klingspor.com
$209.25
117
ROUTER BITS
Router Bits
GLUE JOINTS
